Notice:We have US Warehouse,all of your shipping address from United States will be send in US directly by USPS.
Features:
The Remote Transmitter & the Collar Receiver can be Rechargeable and waterproof.
100 levels of vibration & static(levels can be altered by use of up & down button.)
LCD Display
The Collar length can be adjustable from 12" to 21"
Remote range up to 300 Yards(no block)
Effective on 10 to 130 pounds of dogs
The system can be used for 1 or 2 receiver. (The additional receiver must be the same type as your previous one and purchased from us, this package only included 2pcs receiver.
The Collar Receiver will TURN OFF if it is unused for 4 minutes.
Any move ment will activate the Collar Receiver into STANDBY MODE.
The Transmitter will go into STANDBY MODE if there is no operation after 20 second and turn off after 2 minutes.
Prepare the Remote Transmitter
Charge the Remote Transmitter
1.Connect the charger connector to the charging jack.
2.Plug the charger into a standard outlet.
3.The red light on the Transmitter will be lighted.
4.Charge the Transmitter at least 6 hours for the first charger.
5.After fully charged,the red led will be turned off automatically.
Low battery indicator:the symbol will show up on the right down side of LCD screen.
How to Use the Transmitter
1.To turn on/off the Transmitter,hold the Mode button for 5 seconds.
2.Set to the different modes by pressing the Mode button-the LCD images will change.
3.Press the up and down buttons on right hand side to set level.
4.Choose the different channels for 1 or 2 receivers.
5.The Transmitter will go into STANDBY MODE if not operated for 20 seconds and will TURN OFF if not operated for 2 minutes.
6.In STANDBY MODE,press any button (except LED light button)to wake it up.
Prepare the Collar Receiver
Charge the Collar Receiver
1.Connect the charger connector to the charging jack.
2.Plug the charger into a standard outlet.
3.The red LED light inside the Collar Receiver will be lighted.
4.Charge the Collar Receiver at least 6 hours for the first charge.
5.After fully charged,the red LED light will be turned off automatically.
6.When charging is completed,replace the rubber cover.
Low battery indicator:the Collar Receiver will keep beeping for 2 minuets unless it gets charged.
Connect the Transmitter with the Collar Receiver
1.Turn on the Transmitter and choose 1or 2 channels to encode.
2.Lift the Reset part of Rubber cover in the Collar Receiver.
3.With a pen or paper clip,press the Reset Button inside the Collar Receiver.
4.After a beep from the Collar Receiver,press the LAUNCH button on Transmitter immediately.
5.The Collar Receiver will beep-it is now encoded to the Transmitter.
6.After Encoding is completed,replace the rubber cover back.
We are special in pets products,pls check more in our store
Features:
The Remote Transmitter & the Collar Receiver can be Rechargeable and waterproof.
100 levels of vibration & static(levels can be altered by use of up & down button.)
LCD Display
The Collar length can be adjustable from 12" to 21"
Remote range up to 300 Yards(no block)
Effective on 10 to 130 pounds of dogs
The system can be used for 1 or 2 receiver. (The additional receiver must be the same type as your previous one and purchased from us, this package only included 2pcs receiver.
The Collar Receiver will TURN OFF if it is unused for 4 minutes.
Any move ment will activate the Collar Receiver into STANDBY MODE.
The Transmitter will go into STANDBY MODE if there is no operation after 20 second and turn off after 2 minutes.
Prepare the Remote Transmitter
Charge the Remote Transmitter
1.Connect the charger connector to the charging jack.
2.Plug the charger into a standard outlet.
3.The red light on the Transmitter will be lighted.
4.Charge the Transmitter at least 6 hours for the first charger.
5.After fully charged,the red led will be turned off automatically.
Low battery indicator:the symbol will show up on the right down side of LCD screen.
How to Use the Transmitter
1.To turn on/off the Transmitter,hold the Mode button for 5 seconds.
2.Set to the different modes by pressing the Mode button-the LCD images will change.
3.Press the up and down buttons on right hand side to set level.
4.Choose the different channels for 1 or 2 receivers.
5.The Transmitter will go into STANDBY MODE if not operated for 20 seconds and will TURN OFF if not operated for 2 minutes.
6.In STANDBY MODE,press any button (except LED light button)to wake it up.
Prepare the Collar Receiver
Charge the Collar Receiver
1.Connect the charger connector to the charging jack.
2.Plug the charger into a standard outlet.
3.The red LED light inside the Collar Receiver will be lighted.
4.Charge the Collar Receiver at least 6 hours for the first charge.
5.After fully charged,the red LED light will be turned off automatically.
6.When charging is completed,replace the rubber cover.
Low battery indicator:the Collar Receiver will keep beeping for 2 minuets unless it gets charged.
Connect the Transmitter with the Collar Receiver
1.Turn on the Transmitter and choose 1or 2 channels to encode.
2.Lift the Reset part of Rubber cover in the Collar Receiver.
3.With a pen or paper clip,press the Reset Button inside the Collar Receiver.
4.After a beep from the Collar Receiver,press the LAUNCH button on Transmitter immediately.
5.The Collar Receiver will beep-it is now encoded to the Transmitter.
6.After Encoding is completed,replace the rubber cover back.
We are special in pets products,pls check more in our store
